PROFIBUS Slave
New Features:
- PSDPS-501: provide new HIL_1163.GSD for comX modules (netX variant independent)
New Features:
Changes:
Bugs:
- PSDPS-487: Data of device data provider is not evaluated on netx52
Changes:
Bugs:
- PSDPS-487: Data of device data provider is not evaluated on netx52
New Features:
- PSDPS-474: Add support of new database files with additional modul configuration
Changes:
Bugs:
- PSDPS-486: netx52: wrong ulSystemStatus
- PSDPS-485: Add parameter check for alarm type at alarm notification request
- PSDPS-483: Set Configuration packet is not rejected when database configuration is available
- PSDPS-482: I/O-length not displayed at extended status block
- PSDPS-473: I&M0 Settings are set to default
- PSDPS-470: Stack is at unexpected state after fast BusOff, BusOn sequence
- PSDPS-467: [NJ100] Rotary switch evaluation not working as expected
Bugs:
Bugs:
- PSDPS-470: Stack is at unexpected state after fast BusOff, BusOn sequence
New Features:
- PSDPS-411: Improve error code handling in PROFIBUS_APS_SET_CONFIGURATION_REQ
- PSDPS-369: set network state to Offline after watchdog error
- PSDPS-313: Add new error codes for APS/FSPMS reset pending
Changes:
- PSDPS-465: update to rcX V2.1.11.9 and V2.0.8.32
- PSDPS-462: PROFIBUS_APS_WARMSTART_PRM_REQ is no longer supported
Bugs:
- PSDPS-467: [NJ100] Rotary switch evaluation not working as expected
- PSDPS-464: Transmission type is not set at RCX_GET_DPM_IO_INFO_REQ
- PSDPS-458: Invalid use of TLR_BOOLEAN in API Header
- PSDPS-455: NXLOM SharedMemory example contains wrong comment regarding module configuration
- PSDPS-447: Setting of 'No_Alarm_Supported' flag at set configuration request does not reject configured alarms
- PSDPS-446: NCF_Communicating Bit is not cleared synchronous when process data is unvalid
- PSDPS-361: Boot Medium bit's are incorrectly set for HXNX50
- PSDPS-357: NJ 10 fails on high DPV1 Read/Write load
- PSDPS-350: Bus ON is not set on sending a PROFIBUS_FSPMS_INIT_MS0_REQ.
- PSDPS-348: Get_Cfg reports some cfg data while stack are unconfigured
- PSDPS-182: Duplicate use of error codes
New Features:
- PSDPS-453: feature: Implement a mechanism to read out some parameters from the stack
Changes:
- PSDPS-465: update to rcX V2.1.11.9 and V2.0.8.32
Bugs:
- PSDPS-454: Global Control Clear does not update SAP 57 ReadOutput
- PSDPS-452: No alarm sequence possible after master configured slave without alarm sequence
- PSDPS-451: Alarm specifier is wrong on slow bus cycles if more than one is triggered in a short time
- PSDPS-450: Diagnosis request is signalled without new diagnosis in buffer
- PSDPS-449: Pending alarm may be overwritten from diagnosis
- PSDPS-448: configuring more than 244 I/O modules may crash firmware
- PSDPS-445: On a disturbed bus multiple PROFIBUS_FSPMS_CMD_CHECK_USER_PRM_IND are send
Bugs:
- PSDPS-452: No alarm sequence possible after master configured slave without alarm sequence
Bugs:
- PSDPS-454: Global Control Clear does not update SAP 57 ReadOutput
Bugs:
- PSDPS-444: Extended Status block - mixed data length information
- PSDPS-442: Slave responds with "NotSupported" instead "PrmRequest"
- PSDPS-440: Fileheader reports old/wrong module information
- PSDPS-439: Update Profibus DL V2.1.7.0
- PSDPS-438: General Diagnostic is not displayed at SYCON.net
Bugs:
- PSDPS-444: Extended Status block - mixed data length information
- PSDPS-442: Slave responds with "NotSupported" instead "PrmRequest"
Bugs:
- PSDPS-440: Fileheader reports old/wrong module information
- PSDPS-439: Update Profibus DL V2.1.7.0
- PSDPS-438: General Diagnostic is not displayed at SYCON.net
New Features:
- PSDPS-435: If no additional user parameter are configured accept 7 octett SetPrm
Changes:
Bugs:
- PSDPS-422: WRMSTRT_FLG_NO_ALARM_SUPP requires Alarm_Sequence_Mode_Count=32
- PSDPS-378: SIMATIC module diagnostic shows incorrect HW revision for CIFX
- PSDPS-376: fNewFlag remains set when no connection with master
- PSDPS-375: Error counter are incremented by 2 for cable disconnecion
- PSDPS-373: missing SIF cfg data validation
- PSDPS-372: Missing bCfgLen validation leads to crash
- PSDPS-362: ulHWFeatures value depends of stack state
- PSDPS-349: No validation of bSlaveAddr variable in the PROFIBUS_FSPMS_INIT_MS0_REQ available.
- PSDPS-347: fClearFlag not set when data is cleared
- PSDPS-326: New configuration pending flag is always set.
- PSDPS-227: DMA shall not started with 0 length
Bugs:
- PSDPS-421: Update ProfibusDL to V2.1.6.0
- PSDPS-420: Init_Ms0_req reference->reads uninitialized pointer
- PSDPS-419: Wrong validation state of output data between FSPMS and AP task
- PSDPS-418: On bus cycle times < 300µs the FSPMS fails to send state_changed_ind and does not stop DL-task
Changes:
Changes:
- PSDPS-405: cyclic I/O connection is rejected when less than 5 bytes parameter data are used at GSD
Bugs:
- PSDPS-406: receiving invalid SetSlaveAdr profibus telegram (length < 4 bytes) leads to undefinded stack behaviour
Bugs:
- PSDPS-404: I&M 0 states that I&M is implemented according withdrawn I&M specification v1.2
- PSDPS-402: I&M handling for slot != 0 no longer working after cable reconnect
- PSDPS-401: COMM_COS_READY and COM_COS_RUN bit not correctly handled on channel init
New Features:
Bugs:
- PSDPS-394: Firmware sometimes stuck after channel init
- PSDPS-392: [netX51], [netX52]: Firmware does not start
- PSDPS-390: NJ100 device not recognized correctly by Network Scan
- PSDPS-387: Set Config are accepted when should not
- PSDPS-385: [cifX]: Firmware does not start due to wrong HW option in FileHeader
- PSDPS-384: [netX51], [netX10]: Wrong file header
- PSDPS-275: With existing config.nxd SetConfig is accepted but not used
New Features:
Bugs:
- PSDPS-370: wrong alarmhandling if master sends unexpected alarm ack after configure prior data exchange
Bugs:
- PSDPS-358: [NXHX - 50] - Firmware blocks right after FW download
New Features:
- PSDPS-354: update Profibus HAL to Version 1.5.1
Bugs:
- PSDPS-356: [netX500]: Firmware header contains wrong chip type entry
- PSDPS-341: Configuration failed when application controlled startup is selected in warmstart param
- PSDPS-334: [cifX]: specific inibatch cfg can block firmware
- PSDPS-333: ERR led state are incorrect in case of wrong configuration
- PSDPS-332: ERR Led state is not correct in case of watchdog error
- PSDPS-331: COM port does not work on NETX51 target.
- PSDPS-329: loadable Firmware can not be opened with Tag List Editor
- PSDPS-328: [NXHX 50] - COM LED not functional
Bugs:
- PSDPS-353: Wrong communication state if master changes bus modes: operate -> clear -> stop -> clear
- PSDPS-352: Slave adoption by Class 2 master does not work.
- PSDPS-351: I&M functions doesn't handle >state conflict< correct and accepts every I&M index to be written